A & L Fiberglass Products Custom Molds (321) 631-6616

Masters  Available: 

Floating Bowls:

( Reusable Fiberglass Backpour Hats are also available for many of these)

Laguna Style Recessed Oval,  18” x 22-3/4” x 6” deep –  New Style

Hilo Shell w/Soap Dishes,  13-1/8” x 18-7/8” x 5-5/8” deep

Savannah Style,  13-1/2” x 20” x 6-5/8” deep

Malibu Style, 12-3/4” x 18-3/8” x 6-1/4” deep

Redondo Style, 10-3/8” x 15-1/8” x 6” deep

Newport Style, 14” x 17” x 5-1/2” deep

Deep Newport Style, 14-1/8 x 17-1/2 x 6-1/2 deep

LaPaz Style, 13-1/2” x 19” x 6-1/2” deep

Canadian Oval Style, (Large), 13-3/4” x 20” x 6-3/4” deep

Super Bowl I Style, 12-7/8” x 19-7/8” x 6-1/4” deep

Super Bowl I w/Soap Dishes, 12-7/8” x 19-7/8: x 6-1/4” deep

Super Bowl II, 15-3/4” x 9-1/4” x 6-1/4” deep

Super Bowl III, 13-3/4” x 9-1/4” x 5-7/8” deep

Catalina Style, 11-5/8” x 15-1/8” x 5-1/2” deep

Wave Style Bowl, 12” x 20” x 6″ deep

Small Wave Style Bowl, 17 3/8” x 12” x 5 -3/8” deep

Small Deep Wave Style Bowl, 17 ¾” x 12” x 5-3/4 “ deep

Mini-Wave Bowl, 17” x 10”

All measurements are approximate.



33” x 16” Double Kitchen Sink, Floater w/Hat


Bath Accessories 

16” Cone Vessel, 2-Piece Mold Set

Corner Oval Shower Seat, Textured, 2-Piece Mold Set

Towel Bar Ends/Ring Holder 2-Piece Mold Set (makes three pieces)


Sweetheart IV Soap/Shampoo, 2-Piece Mold Set

Sweetheart Short Soap Dish. 2-Piece Mold Set


Diamond Corner Soap/Shampoo, 2-Piece Mold Set

Sm. Diamond Soap/Shampoo. 2-Piece Mold Set

Diamond Soap Dish, 2-Piece Mold Set

Recessed Soap Ledge (Diamond Single Soap/Shampoo), 2-Piece Mold Set

Diamond Toilet Tissue Holder 2-Piece Mold Set


Opal Toilet Tissue Holder, 2-Piece Mold Set

Opal Shampoo Holder, 2-Piece Mold Set

Opal Soap Dish, 2-Piece Mold Set



All molds are 100% hand laid vinylester construction with HK Research Hybrid Vinylester Tooling Gelcoat

Wood structural reinforcement where needed is 7 ply plywood (no particle board is ever used)


Bowl Construction:

In addition to a ¾ oz skin coat, there are 6 layers of 1-1/2 oz mat and an overlapping layer of 10 oz cloth to finish. With a little care in handling, that will produce a long lasting tool.


I usually treat the new molds with  Mold Sealer and Mold release Interface.  I can skip this part of the process for a customer who prefers to use their own releasing system.


All measurements are approximate.